Your cart is empty.
Your cart is empty.Product Description
The Rheem SP14410 is a Piezo ignitor and bracket. HVAC replacement part Rheem SP14410. Get your system working properly once again with replacement parts.
From the Manufacturer
The Rheem SP14410 is a Piezo ignitor and bracket. HVAC replacement part Rheem SP14410. Get your system working properly once again with replacement parts.
andreas h.
Reviewed in the United States on March 14, 2025
Worked with the gas water heater. Easy to repalce the stock ignitor with this one.
TiTi
Reviewed in the United States on February 16, 2025
Got this when my water heater igniter went out and this brought it straight back to life thankfully! Super easy to replace old one and functions great had my water heater back up and running in seconds!
Arturo Pérez Acosta
Reviewed in Mexico on January 17, 2025
Un gran refacción para que funcione mi boiler
Yucel Yasin Cebi
Reviewed in the United States on April 28, 2025
Just as I needed. Works great!
sparkymark
Reviewed in the United States on September 3, 2024
It wasn't a exact fit but it worked well. Had to shorten the wire so no returnsI gave it a 4 for what I used it for but the sparker is a 5 all day long.
DK
Reviewed in the United States on September 29, 2024
Installed a couple months ago, so far so good. My hot water heater ignitor gave up (Rheem). Took a bit of troubleshooting to figure out it was this part, but once I installed I got the pilot to start up right away.
Tim Shepherd
Reviewed in the United States on August 22, 2024
I bought this for a different brand of a gas water heater. It was an easy install of less than 5 minutes and I spent most of that time modifying something on the connection to my old tank to get it to work.My pilot light started on the first spark.
Charlie
Reviewed in Mexico on May 20, 2024
No sabes cuñado te hará falta siempre es necesario contar con este repuesto el cual es de calidad, durable y muy fácil de instalar
Nick D.
Reviewed in the United States on May 1, 2024
This works perfectly as a replacement with a few modifications. The igniter wire protrudes from a square plastic housing. That housing needs to be ground down to allow the igniter to fit.The igniter wire obviously needs to be cut to the right length and the insulation stripped just a bit. Note that the insulation is thicker than the original igniter wire but it'll still fit with some help. Keep that in mind when trimming the wire.The igniter seemed to be a hair shorter than the original so when I'd push the button, it wouldn't always click. I had to shim it to work. I cut a circle from a piece of packaging plastic and put it inside of the push button. That was the perfect thickness to get it to light every time.
Herb the Hammer
Reviewed in the United States on April 3, 2024
We installed a new 40 gallon gas hot water heater. It was a very hard install because of the very tight space we had to work with. We get all done and the dumb thing will not light. YES, brand new, not a dent or scratch on unit. It was the stupid defective igniter. We never even removed the old one out of its plastic case. Unplugged the old one, plugged in the new one and success. The pilot lit and it fired up great. We just tie rapped the new igniter to the wire there and did not even remove the old one. Time it took to install, 30 seconds. The cost, dirt cheap. Thank you to whoever sold this part. By the way, our unit was not a Rheem. from a very happy customer.
Rick L
Reviewed in Canada on February 9, 2021
Worked as described, no issues after install
Watchdog507
Reviewed in Canada on September 24, 2020
One of our Rheem water heaters had this igniter fail. This was a drop in replacement. Inexpensive and works as it should. Saved me a $300 house call from our HVAC guy.
Lord of the Universe
Reviewed in Canada on August 13, 2019
I didn't end up needing it. Mine was actually still working but the price was really good so I'll keep it because it's a really impossible part to find in a regular store. It's the OEM part for my Rheem hot water heater.
Recommended Products
