Shopping Cart

Your cart is empty.

Your cart is empty.

XMT-MOTO Motorcycle Fuel Vacuum Carburetor Synchronizer carb sync Gauge Fit Honda Yamaha

4.9 (13) Write Review
Free shipping on orders over $29.99

$54.49

$ 26 .99 $26.99

In Stock
  • Aftermarket Parts 100% Brand New
  • Each 2" gauge features 0-76cm/hg readings, shut off valve and all hardware is high brass finish for longer life,higher corrosion resistance and better flow accuracy.
  • Air flow control is handled by needle and seat valves instead of knobs. This helps to resist the dial indicator "bounce" associated with many other lower quality gauges. Set comes complete with red mold storage case.
  • This kit lets you synchronise the values of the 4 carburettors as well as adjust/set them.


Product Description

1
1
1
1
1
1

Package Included:

√ - 4 pcs3-1/2" synchronizer gauges with fixed plate (vacuum)
√ - 4 rubber pipes 8x5x750mm
√ - 4 Tubes of extension 3.9x52mm and 4 tubes 3.9x122mm
√ - 8 Tubes of conical type connector 8x40mm
√ - 4 Tubes 10x53mm ( M6x0.75)
√ - 4 Tubes 10x60mm ( M6x1.0)

Art Gorden
Reviewed in the United States on February 14, 2025
No dislikes . Used to test and set several different carburetors . Constructed well .
G. M.
Reviewed in the United States on June 5, 2024
I don't have to sync carbs very often, so I didn't want to dump a ton of cash on a set of gauges. These have worked good for me. Well worth the money and it comes with a couple thread sizes and non threaded brass lines.
Captain Salty
Reviewed in the United States on June 29, 2024
worked quite well for the money and was easy to use. the one piece was not thread locked so it got stuck in the carb but i put some on it and screwed it back in and waited for it to dry then it all came out easy.
Rochelle Cain
Reviewed in the United States on December 10, 2024
Works as intended. Easy to use. Decent quality for the money and it all fits nicely in the case
Caleb Farmer
Reviewed in the United States on October 28, 2024
This works well with no complaints. I’ve used it on a v-twin bike and my buddy used it on a v4 bike he has. Worked great for both instances.
Pamela J Watkins
Reviewed in the United States on October 12, 2024
The media could not be loaded.
BIG AL
Reviewed in the United States on October 3, 2023
For as seldom as I'll need use they will do fine
Otavio
Reviewed in Canada on August 12, 2019
Work great
Cs
Reviewed in Canada on July 3, 2019
Works as advertised
Paul Morin
Reviewed in Canada on July 25, 2019
Nice product, good customer service.
Dean
Reviewed in Canada on July 15, 2019
Was a little damaged in shipping but I managed to straighten it out also the gauges were not all reading zero so I popped the lenses off and zeroed them and now they work great
Zipperzapper
Reviewed in Canada on September 1, 2018
Well made, nice set of adapters and seller was very nice to dealwith. THANKS
Mini F.
Reviewed in the United States on November 25, 2018
one cylinder on my venture royale would go from a high vacuum to a high pressure, which relocated the needle on that gauge to rest (unhooked) at 60" of vacuum. using a five port, 3/16" ford vacuum manifold i had i hooked up 3 gauges to that one cylinder, and the other gauge to the back cylinder on that side. (the other side was fine with synchronization) . this allowed the gauges to work properly and i synced those 2 carbs. the other side carbs were synced to each other fine, and the 2 sets were fine. next time i will get mercury gauges if i ever need to buy again.perhaps some inline restrictions are in needed in addition to the knobs on the gauges.i have reset that needle but am suspicious of that gauge.