Shopping Cart

Your cart is empty.

Your cart is empty.

Aluminum Fan Spacer 2' Thick 5/8' Pilot With Bolts Washers Machined

Free shipping on orders over $29.99

$37.16

$ 16 .99 $16.99

In Stock
  • Meets or exceeds all original equipment specifications
  • Unsurpassed quality for you can trust
  • Validated for fit, form and function
  • Designed for repair and everyday environment



Product Description

Cobra-tek, cobra-tek parts, cobra-tek Dipstick
timing chain cover
aluminum fan spacer

aluminum fan spacer

All our products are new and have not been used, they are sent in sealed boxes

  • More than 10 years back us

Aluminum Fan Spacer 2" Thick 5/8" Pilot With Bolts Washers Machined

When replacing a Clutch Fan with a Flex Fan, a spacer is often required. The Fan Spacer takes up the area where the clutch used to be. This properly locates the new fan in the shroud. Without the spacer, the fan could hit other engine parts.

  • This extruded aluminum fan spacer allows you to properly position your fan for maximum air flow
  • Comes complete with hardware to simplify installation
  • Kit comes with 5/16" bolts and washers to eliminate fan clutch from fan assembly
fan spancer

Features

The Flex-a-lite fan spacer is to be used when original equipment fan clutch is removed from the engine, to bring the new fan back into the "sweet spot" in the fan shroud opening. Belt driven fans perform best when they are 3/4" to 1" from the radiator's surface. Multiple spacers may be used, up to a maximum of 3 inches.

  • 2" thick for proper spacing when attaching fan
  • 3/4" female pilot for some Fords and Corvettes
  • 2.75" bolt required for proper installation
  • Astandard 5/8" pilot hole for easy replacement
timing chain cover

Kenny
Reviewed in the United States on February 17, 2021
Does what it’s supposed to do.
Tonya Miller
Reviewed in the United States on January 25, 2021
I put this on a 1989 comanche. it was a very tight fit to the pilot hole and i had to screw on just the spacer without fan to seat it then remove bolts and put fan on. Construction seems good and the bolts fit fine.
will orton
Reviewed in the United States on April 10, 2021
Works perfectly
mcard
Reviewed in the United States on December 30, 2020
Fit as described, no issues so far. Better looking than my stock spacer.
tammy mccrary
Reviewed in the United States on October 6, 2020
It works and fit good
RKF
Reviewed in the United States on October 19, 2020
Replacing a stock fan spacer out of necessity. When I replaced my stock fan for the flexi-fan, the pitch of the blades when the car was idling was too close to the shroud, thereby causing it to rub. That spacer was 2-7/8". I was able to pull it closer to the engine and away from the radiator/shroud and also enabled me not to cut up my knuckles while trying to install the fan.The only issue I had was that the center alignment hole was a tad tight, so I had to use my dremel to hone out the opening a little bit to ensure a snug fit, without binding too much. The only other complaint I have is the edges were pretty sharp; it's nice aluminum and has a nice design, I just wish they would have knocked down the sharp edges.Overall, I'm really happy with the product. It has slotted holes for mounting the fan, which allows for inserting the bolts one at a time (at an angle, if necessary), instead of all four at once fearing they may fall out while you line it up. I also like that it looks good in the engine compartment. A nice addition to the vehicle and lightens the load on the pulley at the same time.
Recommended Products

$8.00

$ 3 .99 $3.99

5.0
Select Option

$10.95

$ 4 .99 $4.99

4.8
Select Option

$15.32

$ 6 .99 $6.99

4.8
Select Option

$26.94

$ 11 .99 $11.99

4.4
Select Option

$90.05

$ 36 .99 $36.99

4.8
Select Option

$59.93

$ 30 .99 $30.99

4.7
Select Option

$43.11

$ 22 .99 $22.99

4.9
Select Option